Cookies disabled Find out more
Cookies on the BMW UK website
We use cookies to ensure that we give you the best experience on our website. If you continue without changing your settings, we’ll assume that you are happy to receive all cookies on the BMW UK website. However, if you would like to, you can change your cookie settings at any time. You can find detailed information about how cookies are used on this website by clicking on ‘Find out more’. Find out more

TECHNICAL DATA.

Consumption

Urban (ltr/100km)

- [5.5]

Urban (mpg)

- [51.4]

Extra-urban (ltr/100km)

- [4.1]

Extra-urban (mpg)

- [68.9]

Combined (ltr/100km)

- [4.6]

Combined (mpg)

- [61.4]

CO2 emissions (g/km) upper band

- [132.0]

CO2 emissions (g/km)

- [122.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [6.2]

Weight

Unladen (EU) (kg)

- [1870]

Max permissible (kg)

- [2490]

Max permissible (lbs)

- [5490]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1195/1360]

Permitted axle load, front/rear (lbs)

-/- [2635/2998]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.9]

Urban (mpg)

- [47.9]

Extra-urban (ltr/100km)

- [4.4]

Extra-urban (mpg)

- [64.2]

Combined (ltr/100km)

- [5.0]

Combined (mpg)

- [56.5]

CO2 emissions (g/km)

- [132.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [6.2]

Weight

Unladen (EU) (kg)

- [1870]

Max permissible (kg)

- [2490]

Max permissible (lbs)

- [5490]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1195/1360]

Permitted axle load, front/rear (lbs)

-/- [2635/2998]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.7]

Urban (mpg)

- [49.6]

Extra-urban (ltr/100km)

- [4.3]

Extra-urban (mpg)

- [65.7]

Combined (ltr/100km)

- [4.8]

Combined (mpg)

- [58.8]

CO2 emissions (g/km) upper band

- [132.0]

CO2 emissions (g/km)

- [127.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [6.2]

Weight

Unladen (EU) (kg)

- [1870]

Max permissible (kg)

- [2490]

Max permissible (lbs)

- [5490]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1195/1360]

Permitted axle load, front/rear (lbs)

-/- [2635/2998]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.3]

Urban (mpg)

- [53.3]

Extra-urban (ltr/100km)

- [4.0]

Extra-urban (mpg)

- [70.6]

Combined (ltr/100km)

- [4.5]

Combined (mpg)

- [62.8]

CO2 emissions (g/km) upper band

- [129.0]

CO2 emissions (g/km)

- [119.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [6.1]

Weight

Unladen (EU) (kg)

- [1830]

Max permissible (kg)

- [2450]

Max permissible (lbs)

- [5401]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1175/1340]

Permitted axle load, front/rear (lbs)

-/- [2590/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.8]

Urban (mpg)

- [48.7]

Extra-urban (ltr/100km)

- [4.4]

Extra-urban (mpg)

- [64.2]

Combined (ltr/100km)

- [4.9]

Combined (mpg)

- [57.6]

CO2 emissions (g/km)

- [129.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [6.1]

Weight

Unladen (EU) (kg)

- [1830]

Max permissible (kg)

- [2450]

Max permissible (lbs)

- [5401]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1175/1340]

Permitted axle load, front/rear (lbs)

-/- [2590/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.5]

Urban (mpg)

- [51.4]

Extra-urban (ltr/100km)

- [4.2]

Extra-urban (mpg)

- [67.3]

Combined (ltr/100km)

- [4.7]

Combined (mpg)

- [60.1]

CO2 emissions (g/km) upper band

- [129.0]

CO2 emissions (g/km)

- [124.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [6.1]

Weight

Unladen (EU) (kg)

- [1830]

Max permissible (kg)

- [2450]

Max permissible (lbs)

- [5401]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1175/1340]

Permitted axle load, front/rear (lbs)

-/- [2590/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.7]

Urban (mpg)

- [49.6]

Extra-urban (ltr/100km)

- [4.3]

Extra-urban (mpg)

- [65.7]

Combined (ltr/100km)

- [4.8]

Combined (mpg)

- [58.8]

CO2 emissions (g/km) upper band

- [137.0]

CO2 emissions (g/km)

- [127.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.8]

Weight

Unladen (EU) (kg)

- [1900]

Max permissible (kg)

- [2540]

Max permissible (lbs)

- [5600]

Permitted load (kg)

- [715]

Permitted load (lbs)

- [1576]

Permitted axle load, front/rear (kg)

-/- [1220/1370]

Permitted axle load, front/rear (lbs)

-/- [2690/3020]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.1]

Urban (mpg)

- [46.3]

Extra-urban (ltr/100km)

- [4.6]

Extra-urban (mpg)

- [61.4]

Combined (ltr/100km)

- [5.2]

Combined (mpg)

- [54.3]

CO2 emissions (g/km)

- [137.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.8]

Weight

Unladen (EU) (kg)

- [1900]

Max permissible (kg)

- [2540]

Max permissible (lbs)

- [5600]

Permitted load (kg)

- [715]

Permitted load (lbs)

- [1576]

Permitted axle load, front/rear (kg)

-/- [1220/1370]

Permitted axle load, front/rear (lbs)

-/- [2690/3020]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [5.9]

Urban (mpg)

- [47.9]

Extra-urban (ltr/100km)

- [4.4]

Extra-urban (mpg)

- [64.2]

Combined (ltr/100km)

- [5.0]

Combined (mpg)

- [56.5]

CO2 emissions (g/km) upper band

- [137.0]

CO2 emissions (g/km)

- [132.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.8]

Weight

Unladen (EU) (kg)

- [1900]

Max permissible (kg)

- [2540]

Max permissible (lbs)

- [5600]

Permitted load (kg)

- [715]

Permitted load (lbs)

- [1576]

Permitted axle load, front/rear (kg)

-/- [1220/1370]

Permitted axle load, front/rear (lbs)

-/- [2690/3020]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

195 (265)/4000

Max torque (Nm/rpm)

620/2000-2500

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.3]

Urban (mpg)

- [44.8]

Extra-urban (ltr/100km)

- [4.3]

Extra-urban (mpg)

- [65.7]

Combined (ltr/100km)

- [5.0]

Combined (mpg)

- [56.5]

CO2 emissions (g/km) upper band

- [142.0]

CO2 emissions (g/km)

- [132.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.3]

Weight

Unladen (EU) (kg)

- [1975]

Max permissible (kg)

- [2570]

Max permissible (lbs)

- [5666]

Permitted load (kg)

- [670]

Permitted load (lbs)

- [1477]

Permitted axle load, front/rear (kg)

-/- [1270/1360]

Permitted axle load, front/rear (lbs)

-/- [2800/2998]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

235 (320)/4400

Max torque (Nm/rpm)

680/1750-2250

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.8]

Urban (mpg)

- [41.5]

Extra-urban (ltr/100km)

- [4.6]

Extra-urban (mpg)

- [61.4]

Combined (ltr/100km)

- [5.4]

Combined (mpg)

- [52.3]

CO2 emissions (g/km)

- [142.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.3]

Weight

Unladen (EU) (kg)

- [1975]

Max permissible (kg)

- [2570]

Max permissible (lbs)

- [5666]

Permitted load (kg)

- [670]

Permitted load (lbs)

- [1477]

Permitted axle load, front/rear (kg)

-/- [1270/1360]

Permitted axle load, front/rear (lbs)

-/- [2800/2998]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

235 (320)/4400

Max torque (Nm/rpm)

680/1750-2250

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.6]

Urban (mpg)

- [42.8]

Extra-urban (ltr/100km)

- [4.4]

Extra-urban (mpg)

- [64.2]

Combined (ltr/100km)

- [5.2]

Combined (mpg)

- [54.3]

CO2 emissions (g/km) upper band

- [142.0]

CO2 emissions (g/km)

- [137.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.3]

Weight

Unladen (EU) (kg)

- [1975]

Max permissible (kg)

- [2570]

Max permissible (lbs)

- [5666]

Permitted load (kg)

- [670]

Permitted load (lbs)

- [1477]

Permitted axle load, front/rear (kg)

-/- [1270/1360]

Permitted axle load, front/rear (lbs)

-/- [2800/2998]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

235 (320)/4400

Max torque (Nm/rpm)

680/1750-2250

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [9.1]

Urban (mpg)

- [31.0]

Extra-urban (ltr/100km)

- [5.2]

Extra-urban (mpg)

- [54.3]

Combined (ltr/100km)

- [6.6]

Combined (mpg)

- [42.8]

CO2 emissions (g/km) upper band

- [164.0]

CO2 emissions (g/km)

- [154.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.6]

Weight

Unladen (EU) (kg)

- [1845]

Max permissible (kg)

- [2445]

Max permissible (lbs)

- [5390]

Permitted load (kg)

- [675]

Permitted load (lbs)

- [1488]

Permitted axle load, front/rear (kg)

-/- [1155/1340]

Permitted axle load, front/rear (lbs)

-/- [2546/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2998

Capacity (cinch)

183.00

Stroke/Bore (mm)

94.6/82.0

Stroke/Bore (inch)

3.70/3.20

Max output (kW/hp/rpm)

240 (326)/5500-6500

Max torque (Nm/rpm)

450/1380-5000

Compression ratio : 1

11.0

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [9.7]

Urban (mpg)

- [29.1]

Extra-urban (ltr/100km)

- [5.5]

Extra-urban (mpg)

- [51.4]

Combined (ltr/100km)

- [7.0]

Combined (mpg)

- [40.4]

CO2 emissions (g/km)

- [164.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.6]

Weight

Unladen (EU) (kg)

- [1845]

Max permissible (kg)

- [2445]

Max permissible (lbs)

- [5390]

Permitted load (kg)

- [675]

Permitted load (lbs)

- [1488]

Permitted axle load, front/rear (kg)

-/- [1155/1340]

Permitted axle load, front/rear (lbs)

-/- [2546/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2998

Capacity (cinch)

183.00

Stroke/Bore (mm)

94.6/82.0

Stroke/Bore (inch)

3.70/3.20

Max output (kW/hp/rpm)

240 (326)/5500-6500

Max torque (Nm/rpm)

450/1380-5000

Compression ratio : 1

11.0

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [9.4]

Urban (mpg)

- [30.1]

Extra-urban (ltr/100km)

- [5.3]

Extra-urban (mpg)

- [53.3]

Combined (ltr/100km)

- [6.8]

Combined (mpg)

- [41.5]

CO2 emissions (g/km) upper band

- [164.0]

CO2 emissions (g/km)

- [159.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.6]

Weight

Unladen (EU) (kg)

- [1845]

Max permissible (kg)

- [2445]

Max permissible (lbs)

- [5390]

Permitted load (kg)

- [675]

Permitted load (lbs)

- [1488]

Permitted axle load, front/rear (kg)

-/- [1155/1340]

Permitted axle load, front/rear (lbs)

-/- [2546/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2998

Capacity (cinch)

183.00

Stroke/Bore (mm)

94.6/82.0

Stroke/Bore (inch)

3.70/3.20

Max output (kW/hp/rpm)

240 (326)/5500-6500

Max torque (Nm/rpm)

450/1380-5000

Compression ratio : 1

11.0

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.2]

Urban (mpg)

- [45.6]

Extra-urban (ltr/100km)

- [4.2]

Extra-urban (mpg)

- [67.3]

Combined (ltr/100km)

- [4.9]

Combined (mpg)

- [57.6]

CO2 emissions (g/km) upper band

- [139.0]

CO2 emissions (g/km)

- [129.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.2]

Weight

Unladen (EU) (kg)

- [1935]

Max permissible (kg)

- [2530]

Max permissible (lbs)

- [5578]

Permitted load (kg)

- [670]

Permitted load (lbs)

- [1477]

Permitted axle load, front/rear (kg)

-/- [1250/1340]

Permitted axle load, front/rear (lbs)

-/- [2756/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

235 (320)/4400

Max torque (Nm/rpm)

680/1750-2250

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.6]

Urban (mpg)

- [42.8]

Extra-urban (ltr/100km)

- [4.5]

Extra-urban (mpg)

- [62.8]

Combined (ltr/100km)

- [5.3]

Combined (mpg)

- [53.3]

CO2 emissions (g/km)

- [139.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.2]

Weight

Unladen (EU) (kg)

- [1935]

Max permissible (kg)

- [2530]

Max permissible (lbs)

- [5578]

Permitted load (kg)

- [670]

Permitted load (lbs)

- [1477]

Permitted axle load, front/rear (kg)

-/- [1250/1340]

Permitted axle load, front/rear (lbs)

-/- [2756/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

235 (320)/4400

Max torque (Nm/rpm)

680/1750-2250

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [6.4]

Urban (mpg)

- [44.1]

Extra-urban (ltr/100km)

- [4.4]

Extra-urban (mpg)

- [64.2]

Combined (ltr/100km)

- [5.1]

Combined (mpg)

- [55.4]

CO2 emissions (g/km) upper band

- [139.0]

CO2 emissions (g/km)

- [134.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [5.2]

Weight

Unladen (EU) (kg)

- [1935]

Max permissible (kg)

- [2530]

Max permissible (lbs)

- [5578]

Permitted load (kg)

- [670]

Permitted load (lbs)

- [1477]

Permitted axle load, front/rear (kg)

-/- [1250/1340]

Permitted axle load, front/rear (lbs)

-/- [2756/2954]

Engine

Cylinders/valves per cylinder

6/4

Capacity (cc)

2993

Capacity (cinch)

183.00

Stroke/Bore (mm)

90.0/84.0

Stroke/Bore (inch)

3.50/3.30

Max output (kW/hp/rpm)

235 (320)/4400

Max torque (Nm/rpm)

680/1750-2250

Compression ratio : 1

16.5

Wheels

Tyre size front

- [225/60 R17 99Y]

Tyre size rear

- [225/60 R17 99Y]

Wheel size front

7,5J x 17 LM

Wheel size rear

7,5J x 17 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [11.1]

Urban (mpg)

- [25.4]

Extra-urban (ltr/100km)

- [6.1]

Extra-urban (mpg)

- [46.3]

Combined (ltr/100km)

- [7.9]

Combined (mpg)

- [35.8]

CO2 emissions (g/km) upper band

- [189.0]

CO2 emissions (g/km)

- [184.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [4.7]

Weight

Unladen (EU) (kg)

- [1895]

Max permissible (kg)

- [2515]

Max permissible (lbs)

- [5545]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1225/1345]

Permitted axle load, front/rear (lbs)

-/- [2701/2965]

Engine

Cylinders/valves per cylinder

8/4

Capacity (cc)

4395

Capacity (cinch)

268.00

Stroke/Bore (mm)

88.3/89.0

Stroke/Bore (inch)

3.50/3.50

Max output (kW/hp/rpm)

330 (450)/5500-6000

Max torque (Nm/rpm)

650/1800-4500

Compression ratio : 1

10.5

Wheels

Tyre size front

- [245/50 R18 100Y]

Tyre size rear

- [245/50 R18 100Y]

Wheel size front

8J x 18 LM

Wheel size rear

8J x 18 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [11.1]

Urban (mpg)

- [25.4]

Extra-urban (ltr/100km)

- [6.1]

Extra-urban (mpg)

- [46.3]

Combined (ltr/100km)

- [7.9]

Combined (mpg)

- [35.8]

CO2 emissions (g/km) upper band

- [189.0]

CO2 emissions (g/km)

- [184.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [4.7]

Weight

Unladen (EU) (kg)

- [1895]

Max permissible (kg)

- [2515]

Max permissible (lbs)

- [5545]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1225/1345]

Permitted axle load, front/rear (lbs)

-/- [2701/2965]

Engine

Cylinders/valves per cylinder

8/4

Capacity (cc)

4395

Capacity (cinch)

268.00

Stroke/Bore (mm)

88.3/89.0

Stroke/Bore (inch)

3.50/3.50

Max output (kW/hp/rpm)

330 (450)/5500-6000

Max torque (Nm/rpm)

650/1800-4500

Compression ratio : 1

10.5

Wheels

Tyre size front

- [245/50 R18 100Y]

Tyre size rear

- [245/50 R18 100Y]

Wheel size front

8J x 18 LM

Wheel size rear

8J x 18 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.

Consumption

Urban (ltr/100km)

- [11.1]

Urban (mpg)

- [25.4]

Extra-urban (ltr/100km)

- [6.1]

Extra-urban (mpg)

- [46.3]

Combined (ltr/100km)

- [7.9]

Combined (mpg)

- [35.8]

CO2 emissions (g/km) upper band

- [189.0]

CO2 emissions (g/km)

- [184.0]

Tank capacity (ltr)

78

Tank capacity (gals)

17.2

Performance

Top speed (km/h)

- [250]

Acceleration 0-62 mph (sec)

- [4.7]

Weight

Unladen (EU) (kg)

- [1895]

Max permissible (kg)

- [2515]

Max permissible (lbs)

- [5545]

Permitted load (kg)

- [695]

Permitted load (lbs)

- [1532]

Permitted axle load, front/rear (kg)

-/- [1225/1345]

Permitted axle load, front/rear (lbs)

-/- [2701/2965]

Engine

Cylinders/valves per cylinder

8/4

Capacity (cc)

4395

Capacity (cinch)

268.00

Stroke/Bore (mm)

88.3/89.0

Stroke/Bore (inch)

3.50/3.50

Max output (kW/hp/rpm)

330 (450)/5500-6000

Max torque (Nm/rpm)

650/1800-4500

Compression ratio : 1

10.5

Wheels

Tyre size front

- [245/50 R18 100Y]

Tyre size rear

- [245/50 R18 100Y]

Wheel size front

8J x 18 LM

Wheel size rear

8J x 18 LM

Information about the data
Work performed in this package:
Body/electrical equipment.
  • Lighting system is checked.
  • Instrument panel, dashboard illumination, and heater blower fan are checked.
  • Horn, headlight flasher and hazard warning system are checked.
  • Condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle are checked.
  • Acid level and state-of-charge in battery are checked and charged if required.**
  • Microfilter or activated charcoal filter are replaced.**
  • Check water drain below brake booster for contamination, clean if necessary.
  • Change M-Mobility System sealant bottle after 3 years.
  • Check entire body, except cavities, for corrosion.

Engine compartment.
  • Test with diagnostic system is performed to determine if any faults have been automatically recorded by the vehicle.
  • Motor oil and oil filter are removed and replaced with new oil and filter.
  • Coolant levels are checked; when refilled, concentration of fluid is checked.
  • At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
  • Service interval indicator is reset according to factory specifications.
  • Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
  • Steering fluid reservoir is checked and fluid is topped up if needed.
  • At the corresponding interval brake fluid is replaced (every two years at the latest).**

Chassis area.
  • Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
  • Steering system is checked for play, leakage, damage and wear.
  • Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
  • Brake system cables and connections are checked for leaks, damage and correct positioning.
  • Functionality of parking brake is checked and adjusted where needed according to regulations.
  • Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked. 

Final inspection.
  • Roadworthiness is checked including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, and Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.). 

**Additional costs may apply, for further details please contact your BMW Dealer.
Multimedia content activeMultimedia content inactive